Pluto Plus 70MHz – 6GHZ AD9363 SDR Radio Receiver /Transmitter 2x RX/ 2x TX Compatible with ADI ADALM-PLUTO PLUTO

Name: Pluto Plus 70MHz - 6GHZ AD9363 SDR Radio Receiver /Transmitter 2x RX/ 2x TX Compatible with ADI ADALM-PLUTO PLUTO
SKU: 1005002109764566
Availability: InStock

$373.99

USD

NGN

GBP

EUR

1978 in stock

Ask a Question

Get 10$ Off your Total Order Now! Make An Order Now Before This Offer Ends!

SKU: 1005002109764566 Category: Fulfilled by Ominy Market

Promotions

$10.00 OFF

$100.00 OFF

$80.00 OFF

$60.00 OFF

$40.00 OFF

$20.00 OFF

$5.00 OFF

Promotions

10$ OFF

Minimum spend 50$ Maximum spend $

Unlimited time

Apply Coupon

100$ OFF

Minimum spend 1376$ Maximum spend $

Unlimited time

Apply Coupon

80$ OFF

Minimum spend 744$ Maximum spend $

Unlimited time

Apply Coupon

60$ OFF

Minimum spend 620$ Maximum spend $

Unlimited time

Apply Coupon

40$ OFF

Minimum spend 372$ Maximum spend $

Unlimited time

Apply Coupon

20$ OFF

Minimum spend 74$ Maximum spend $

Unlimited time

Apply Coupon

5$ OFF

Minimum spend 15$ Maximum spend $

Unlimited time

Apply Coupon

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Brand Name: LISCN
Certification: CE
Origin: CN(Origin)
Gain(dB): 10
Model Number: Pluto

1.Product Overview:
Pluto+ is a software-defined radio platform that supports 2TX 2RX, supports Gigabit Ethernet and Micro SD card. The design draws on the well-known ADI ADALM-PLUTO and improves its shortcomings.

2.Features：

ADC/DAC：AD9363(Can hack to AD9361 or AD9364)

2 Transmit, 2 Receive channel

RF Range：70MHZ~6GHZ

Ref Clock：VCTCXO 40MHZ0.5ppm

SOC：Zynq7010 FPGA：28k

RAM：512M

FLASH：32M

USB：2.0support OTG

Ethernet：1000Mb

Micro SD can use to boot

DC IN：5V +-0.5V-2AmicroUSB

Interface

Please note that all IO levels are 1.8V.

3.1 When using the official ADI-PlutoSDR firmware, please connect to URST-MI052.

Get 10$ Off your Total Order Now! Make An Order Now Before This Offer Ends!

ominymarket10offby

3.2 When using Pluto+ firmware and need to support Ethernet, please connect URST-MIO46

3.3 When using SD card to boot, please connect SD-H to 1V8

3.4 When using JTAG to debug, please connect JTAG# to GND

3.5 Please connect EXCLK to GND when using external reference clock input

PTT key port

PTT drives optocouplers through GPIO0 (MI00), which requires an external relay or control circuit.

DFU KEY

At any time, you can press the DFU button and power on PLUTO+ again to enter the DFU mode, but you need to connect the URST jumper to MI052

Ref CLK input IPEX

You can connect a cable to input an external high-precision reference clock for AD9363 through the IPEX interface.

The main level should not exceed 3.3V, and the EXCLK jumper needs to be connected to GND to turn off the built-in clock

Calibrate the frequency of the built-in VCTCXO

The frequency of the 40M clock can be fine-tuned by adjusting the adjustable resistor next to the VCTCXO, provided that you have a reference signal source

Micro-SD

Support booting via SD card, need to connect SD-H jumper to 1V8

Refund Policy

Same with Ominy market refund policy

Cancellation / Return / Exchange Policy

Sames as Ominy market cancellation policy

General Enquiries

There are no enquiries yet.

Sponsored

Todays Deal

Pluto Plus 70MHz – 6GHZ AD9363 SDR Radio Receiver /Transmitter 2x RX/ 2x TX Compatible with ADI ADALM-PLUTO PLUTO

Reviews